Plumber's Essentials: What You Need for Bathtub Installation
Plumber's Essentials: What You Need for Bathtub Installation
Blog Article
The article down below relating to How to Install a Bathtub Yourself is incredibly attention-grabbing. You should read it.

Setting up a tub isn't precisely rocket science, however it does call for strong plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably difficult task. If the old bathtub is conveniently available, the task can move quickly; if you need to open up a wall surface to remove the old bathtub and also place the new bathtub, the job is much harder. In either case, the project is within a residence handyman's skills, although you will require an assistant to vacate the old bathtub as well as set in the new one. Ensure you have qualified on your own for the job and fit trying it. Rather than hiring a contractor to take over a halfway-completed project, it is better to consider employing one before you start. Possibilities are you might need an expert plumber to make tube connections.
This post will assist you mount a new tub in your shower room if you have actually currently acquired a brand-new bathtub and also do not require to transform the plan of your previous water supply pipes.
Your devices and also product list ought to make up the following:
Preparing for the Setup
First of all, the sustaining structure supplied with the bath must be fitted (if required) according to the supplier's guidelines. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to see to it that if the tap features a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets unit to prevent stress on the tub.
Fit the flexible tap adapters to the bottom of the two taps making use of 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you utilize every one of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath should now prepare to be suited its last setting.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the water supply. After doing so, switch on the faucets to drain pipes any kind of water remaining in the system. The process of removing the existing faucets can be rather troublesome as a result of the limited access that is frequently the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipes. As soon as the supply pipes have actually been gotten rid of, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from turning throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will have to be cleansed of any type of old sealing compound.
Before proceeding to fit the new faucets, contrast the pipeline connections on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Using the two wood boards under its feet, place the tub in the called for position. The wooden boards are handy in evenly spreading the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 small points.
The following goal is to make sure that the tub is leveled all round. This can be attained by examining the level as well as readjusting the feet on the tub up until the spirit level reads level.
To set up faucets, fit all-time low of the furthest adaptable tap port to the ideal supply pipeline by making a compression sign up with; then do the same for the various other tap.
Activate the water system as well as check all joints as well as brand-new pipework for leakages and also tighten them if essential. Fill up the tub as well as additionally examine the overflow outlet as well as the regular electrical outlet for leakages.
Ultimately, repair the bath paneling as described in the supplier's user's manual. Tiling as well as sealing around the tub must wait until the tub has actually been utilized at least once as this will settle it right into its final position.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to avoid damages to the string. One end of the port fits on the plastic tail of the tap as well as the other end supplies a connection to the current supply pipelines.
If you require to fit a monobloc, then you will certainly require decreasing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin guaranteeing that the washers remain in place in between the faucet and the sink. Safeguard the tap in place with the manufacturer supplied backnut. Once the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical tap ports. The previous type must be attached to the tap finishes initially, tightening only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the location where the bath satisfies the ceramic tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the fitting can move enough to crack a rigid seal, causing the water to permeate the wall surface in between the bathroom and also the tiling, bring about complications with wetness and also feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Remember to constantly load the tub with water prior to sealing, to enable the activity experienced when the bathtub is in usage. The sealer can break relatively very early if you do not take into account this activity before sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also quickly offered on the marketplace. It is suggested to fit the floor tiles using water-resistant or water-proof adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

Do you like reading up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Write a review directly below. We'd be glad to see your suggestions about this content. We are looking forward to see you back again soon. Please set aside a second to share this blog entry if you liked it. Thanks a bunch for your time. Visit again soon.
Professional help? Ring! Report this page